I previously posted this as a response comment in the 'About Flat Tesla Bifilar Coils,' post, and upon reviewing the comment realized it worthy of its own posting discussion thread. Here it is with some revisions to the original comments:
From my studies and what I understand about bifilar coil plats, depending on how they are made they can possess a proximity effect to picking up hertz energy and converting it to a more cohesive longitudinal scalar-type energy, thus better targeting the subtle energy effects such as the ‘strange attractor’ aspect spoken of in theoretical physics for instance, also known in radionics as the ‘operator’ principle.
In my work with various bifilar coil plates of different manufacture, that includes Aplicum bifilar coil plates, that I use with my Heironymous type radionic instruments and array of antennas, both in serial configuration powered by Aplicum amplifiers and singly in-proximity energized (i.e. not directly powered or ‘plugged in’), there is a noted effect upon my radionic instruments performance, such as the assessment stick or pendulum effect being more sharp and clear, as well as more effective transmission/broadcasting in shorter time frames
I don’t recall the source, but a few years ago I read some novel r&d based research that bifilar coil plates made a certain way, if in proximity to an energy field, such as that produced by electrical flow/field, can pick up on it, give it more coherence and longitudinal quality and in turn transmit it accordingly, theoretically as a scalar wave broadcast. I’ve used bifilar coil plates on an in-proximity basis, with noted discernible results. So, even though a bifilar coil plate doesn’t generate aetheric energy in and of itself, it can appear to do so when the in-proximity effect takes place, which is still electrical sourced ’field’ of electromagnetic energy feeding the in-proximity effect.
Has anyone else out there dealing with bifilar coil plates regarding radionics work observed or experienced the same?
(Filip, on another note. I recently acquired your SWCC 2.0 instrument. Very intriguing, especially the digital aspect you have built into the devices. The quality is very good for the affordable price. It appears to be a very forward thought out approach, and one that I understand quite well. I’m very satisfied with the instrument. Thank you and take care.)
I use the coils in a wellness centre and hence not using radionics for remote healing. I am testing different frequencies and seeing what the results are. Not using any of the frequencies published. sorry for the misunderstanding.
eshardelow, you said, "The closer the coils the wider the field gets." Did you mean to imply the coil wraps on the pancake plate itself, or a series of coil plates, i.e 2, 3 or 4 separate plates stacked upon each other with a space between them, implying that the closer the stacked plates the wider the field gets?
To give some context to my questions, I use a number of Aplicum bifilar plates stacked upon each other numbering anywhere from 6 plates to 24 plates (done in series of 6), with a predetermined space between each, that are each connected to an Aplicum bifilar amplifier, thus acting as an ancillary transmitting/broadcasting antenna array for boosting my Heironymous type radionic instruments broadcasting strength.
The results derived from these ancillary stacked bifilar plates as boosting antennas is quite remarkable both in greater targeted coherent transmission of energy signatures coupled with shorter broadcasting times due to the more cohesive nature these ancillary antenna arrays impart to a transmission/broadcast.
yes I have done a few test’s using the coils and tried different amplifierS. What I have found is the scalar wave energy cannot be measured directly. Instead, we can consider the current passing through the link cable, which is directly converted to scalar wave energy. This is in the order of 70.7 mA. The potential difference between the transmitter and receiver coils is approximately 200v. P = I^2 * R. The power being received by the receiver coil is therefore 1 watt. This energy is directly converted to the scalar field, with a very high conversion efficiency. if we use dowsing rods we find if coils are 6 ft apart we get a 6 ft radius like a soccer ball. The closer the coils the wider the field gets.
I hope this helps you.